A guide to port forward Beetel 220BX

Guide to basic Port Forwarding on

BEETEL 220BX ADSL2+ MODEM


Why port forward ?
There are programs that require direct peer to peer connection for maximum efficiency of the connection…these are peer-to-peer applications… like kazaa,bittorrent clients(azureus,utorrent,bitcomet)

What are these ports?
Ports are like ‘logical’ doors…thru which a data is supposed to come into.
Think of like a short cut to your Girlfriends place…u first try to go through the shortest route….(the configured port of the software)..if the route/port is unavailable u try all type of direction & go by some other route/port. This is the simplest explanation that I could think of.

What happens when port is forwarded?
When we port forward , a route to our computer in made available freely…the advantage the data can be received by your machine very quickly & hence the efficiency increases.
(both upload & download speeds are affected )

How to port forward ?
Airtels’ modem 220bx is very simple to port forward…the simplest I’ve come across.
It can be done from telent or thru a browser…assuming u find browser more convenient…I’ve provided screenshots for the same along with each steps.
------------------------------------------------------------------------
Procedure 1 : Browser Interface
------------------------------------------------------------------------
NOTE: The new firmwares seem to hide the NAT option in browser interface & you may get the interface like below,
Image by gulve

dont worry...just follow the Procedure 2 , where u can do the job through TELNET...the keywords & config all are same..only inter

To check whether a ports is open :
Go to
Where 60215 is the port u want to check.

If the result u get is ‘stealth’ , then are ports are not forwarded ( the data should come from long road)

If the result is ‘Closed’, then the port is forwarded but not being used.

If the result is ‘Open’, the port is forwarded & is used

• you must be aware of
  http://192.168.1.1 , this provides basic options for advanced
  options
  u are to go to
  http://192.168.1.1/main.html
  Now go to the 192.168.1.1/main.html
  (password by default is admin,admin or admin,password or admin,123456…if this fails call your
  CC)
  
  
  
  
• After the page opens
  Click on Advanced Setup-->NAT-->Virtual Servers
  
  
  
  
  
• You are supposed to get the image as below
  
  click on custom server give whatever name u want
  Then click on the server ip address…by default if u are using the modem on a single machine the ip address would be 192.168.1.2
  So enter that .
  (u can verify by , command-->ipconfig-->ipaddress . this ipaddress should be entered here)
  
  
  
  
  
  
• Suppose we want to open up port 5000,5001,5002,5003,5004,5005
  then external port & enter 5000 , external port end  5005
  
  
  The internal port start & end would be done automatically.
  (note : u can also open 1 single port by giving external port start & end the same..
  for example…if u want to open port 69999 give the start & end as 69999)
  
  
  
  
• Save & reboot the modem

(End of port forwarding using Browser interface)


------------------------------------------------------------------------
Procedure 2 : TELNET Interface
------------------------------------------------------------------------

• launch cmd & type in
  Code:

  telnet 192.168.1.1
  

• give the authentication info of the modem.
  (password by default is admin,admin or admin,123456…if this fails call your CC)
  
• you see this screen
  Code:

     Main Menu
  
  1.  ADSL Link State
  2.  LAN
  3.  WAN
  4.  DNS Server
  5.  Route Setup
  6.  NAT
  7.  Firewall
  8.  Quality Of Service
  9.  Management
  10. Passwords
  11. Reset to Default
  12. Save and Reboot
  13. Exit
   ->
  

  select 6 & press enter.
  
  
• you will get this screen
  
  
  Code:

     NAT Menu
  
  1. Virtual Server
  2. DMZ
  3. Exit
  / NAT ->
  

  Choose 1 & press enter
  
  
• Code:

     Virtual Server Menu
  
  1. Add
  2. Remove
  3. Show
  4. Exit
  / NAT/Virtual Server ->
  

  Press 1 & press enter
  
  
• Code:

          Virtual Server Add
  
  Note: Hit return at prompt if parameter is not used or to accept default value.
  Press <enter> to use current value
  Press <esc> and <enter> to cancel
  
  Service name ()                             :
  

  Enter a name for the port forward operation..in this case i give it test_1
  
  
• Code:

  Service name ()                             : test_1
  Protocol [0-tcp&udp,1-tcp,2-udp,3-icmp] (1) :
  

  Selecting 0 enables you to forwardboth TCP & UDP(recommended)
  choose 1 & press enter
  
  
• Code:

  Service name ()                             : test_1
  Protocol [0-tcp&udp,1-tcp,2-udp,3-icmp] (1) : 1
  External start port ()                      : 56666
  External end port ()                        : 56668
  Internal start port ()                      : 56666
  Internal end port ()                        : 56668
  Internal server IP address ()               : 192.168.1.2
  

  Enter the code in the above fashion manner. & press enter
  
  By convention External start port & Internal Start port should be the same .
  External end port & External End port should be the same.
  Internal IP address : This is the IP the modem is assigning to your computer.
  by default if u are using the modem on a single machine the ip address would be 192.168.1.2
  So enter that .
  (u can verify by , command-->ipconfig-->ipaddress . this ipaddress should be entered here)
  
  
  Quote:

  Code: OK..so how to give about start port no & end port no? say for example you want to open the port 60000 then give Quote: External start port () : 60000 External end port () : 60000 Internal start port () : 60000 Internal end port () : 60000 If u want to open a series of ports...say for example 60000 to 60010 then give Quote: External start port () : 60000 External end port () : 60010 Internal start port () : 60000 Internal end port () : 60010 after you enter the detials in above manner you will get this message Code: Hit <enter> to continue

  press enter & you will be taken back to this screen.
  
  
  Code:

     Virtual Server Menu
  
  1. Add
  2. Remove
  3. Show
  4. Exit
  / NAT/Virtual Server ->
  

• You have successfully port forwarded.
  for removing the opend port follow the same procedure.
  You may see all the ports opened selecting option 3.
  or come out of telnet by choosing option 4.
  
  
  snapshot of telnet window showing all the forwarded ports.

------------------------------------------------------------------------
(End of port forwarding using TELNET interface)
That’s it you are done port forwarding , u can check the port u forwarded by the link I have give at the beginning of this guide.

If u have any problems while doing this procedure...drop in a request in this thread..& i'll try to sort it out.